LAUNCH X431 S2-2 SENSORBOX/SENSOR SIMULATOR

LAUNCH X431 S2-2 SENSORBOX/SENSOR SIMULATOR

LAUNCH X431 S2-2 SensorBox/Sensor Simulator

LAUNCH S2-2 Sensorbox is designed to test and simulate most vehicle sensors, allowing you to quickly troubleshoot ECU/sensor faults. Simulation of DC signal, pulse signal, predetermined waveform signal simulation - sine waveform, simulating signal of oxygen sensor, mass air flow, injector, throttle position and more. A unique feature is the ability to simulate of "hand-drawn" signals. Multimeter functions: voltage measurement, resistance frequency signal and more.

 

Features:

  1. Check ECU inputs/outputs are correct
  2. It supports manual drawing of waveforms.
  3. Simulate working condition of sensors without replacing parts.
  4. Simulate some special working condition of sensors without replacing parts.
  5. Can be used as Multimeter to measures resistance, voltage AC/DC, capacitance, frequency and pulse signals, etc.
  6. One click to enter the intuitive menu of the sensor, actuator, defined/drawn the waveform, timing waveform, multimeter, system settings.

Functions:

  1. Sensor: Is used to simulate the input signals of the automobile electronic control system, and the automobile computer adjusts the running state of the engine according to these parameters.
  2. Actuator: Is used to simulate the output control signal of automobile electronic control system, so as to judge the working conditions of automobile actuators such as idle motor, EGR solenoid valve, etc.
  3. Multimeter: Through this function, users can test voltage, resistance, and capacitance.

Defined

  1. Waveform: There are 9 waveforms to choose; Forward sine wave, reverse sine wave, forward square wave, reverse square wave, medium voltage, straight line, high / low voltage straight line, triangle wave, and trapezoidal wave.
  2. Frequency: Set the frequency of the selected waveform.
  3. Amplitude: Set the amplitude of the selected waveform.
  4. Offset: Set the offset of the selected waveform.
  5. Phase: Set the phase of the selected waveform.
  6. Duty cycle: Set the duty cycle of the selected waveform.
  7. Signal sync: Can cause CH1 and CH2 to output signals at the same time.

Hand-Drawn

  1. Total frame: 1-3 (optional). Indicate the total number of output points
  2. Generally, one waveform is composed of 100 points. The values 1-3 indicate that you can select 100, 200, or 300 points to form a waveform.
  3. Edit frame: You can edit a single frame or edit all
  4. Waveform: You can select a preset waveform and place it in the hand-drawing area
  5. Frequency: Frequency of a single frame (for 3-frame output, the total frequency is the set frequency/3)
  6. Amplitude: Amplitude of the output waveform
  7. Offset: Offset of the output waveform

Hardware Specifications:

 Launch X-431 O2-2 SensorBox 

 Parameter

Range

 Number of channels

2

 Amplitude range

 0 – 20 V

 Accuracy

 ±1%

 Max output current

 20 mA

 Predefined frequency range

 0 – 20 kHz

 Square wave signal pulse frequency

 0 – 15 kHz

 Square wave signal duty cycle

 0 – 100 %

 Power supply

Simulator sensor output/max current 20mA (output is powered by battery)

Drive solenoid, ignition coil/output current 2A (external power supply)


USB: USB2.0 Type B (with charging and power supply function/5V)

 DC voltage simulation

 Yes

 Fixed frequency simulation

 Yes

 Predefined waveform simulation

 Yes

 Hand-drawn waveform simulation

 Yes

 Signal generator interface

 2

 External power supply port

 1

 Solenoid interface

 1

 Multimeter interface

 2

 Working temperature

 0 °C – 50 °C

 Storage temperature

 -30 °C – 70 °C

  

 Multimeter 

 Parameter

 Range

 DC voltage

 0 V – 700 V

 AC voltage

 0 V – 700 V

 Resistance

 0 Ω – 40 MΩ

 Capacitance

 0 F – 100 µF (maximum 30 s measurement time)

 Diode

 0 V – 1.5 V

 Continuity detection

 Sounds below 30 Ω

Supported languages:

English, Italian, German, Japanese, Russian, French, Spanish, Portuguese, Polish, Turkey, Dutch, Greek, Hungarian, Arabic, Danish, Korean, Farsi, Romanian, Serbian, Finish, Swedish, Czech.

 

Launch X431 S2-2 Sensor box Package List:

  1. 1 x Sensorbox S2-2 main unit
  2. 1 x USB cable A-B type
  3. 1 x Seven core pin test cable
  4. 1 x Double clamp power cable
  5. 2 x HT30 test cable
  6. 1 x Multimeter probe black
  7. 1 x Multimeter probe red
  8. 1 x Needle set
  9. 1 x Four channel oscilloscope with a 6-channel lead, model TA024
  10. 1 x Four channel oscilloscope with a 6-channel lead, model TA025
  11. 1 x Four channel oscilloscope with a 6-channel lead, model TA026
  12. 1 x Power adapter
  13. 1 x User's manual
  14. 1 x Carrying case